what knot to use for steel wire on d ring

Download Commodity

Download Article

When you lot want to hang a framed picture or work of art, i of the most common means to practise and then is by installing picture frame wire so you lot can hang the frame on hooks in the wall. Starting time, screw D-rings into each side of the back of the frame. Then, secure motion-picture show frame wire effectually the D-rings by using slipknots and wrapping information technology around itself. In no time at all, your frame volition be ready to hang!

  1. 1

    Put the frame face down on a flat piece of work surface with the bottom nearest to you. Lay the frame confront upwardly in front end of you first so you are sure the lesser of the frame is closest to you. Carefully flip it over and then y'all are looking at the back side.[1]

    • This will ensure the picture frame is oriented correctly as you lot install the D-rings.
  2. ii

    Put a sticky felt crash-land in each of the bottom corners of the picture frame. Put 1 modest viscous felt bump in each corner. This volition steady it on the wall once information technology is hung and permit air to circulate behind it.[2]

    • You lot can get sticky felt bumps at a craft supply shop, hardware store, or online. They are only small round pieces of felt with an adhesive on the dorsum that you lot peel off a sheet like stickers.

    Tip: Air apportionment behind a picture is important considering if there is no air flow, the picture can suck up moisture from the wall behind information technology and grow mold or get damaged.

    Advertisement

  3. 3

    Mensurate and marker 1/iii of the mode downward from the top of the frame. Use a ruler or measuring tape to measure 1/3 of the way downwards from the pinnacle on 1 side and make a mark with a pencil. Repeat this on the other side.[iii]

    • For example, if the pic frame is 30 cm (12 in) long, make a mark on each side x cm (3.9 in) down from the superlative of the frame.
  4. 4

    Screw a D-ring into each side where you made the marks. Lay the D-rings so the spiral holes line up with your marks and the D shapes face up inwards towards the center of the frame. Attach the D-rings using the provided screws.[4]

    • D-rings are the standard hardware used to install picture frame wire. Yous tin purchase them at a framing supply shop, hardware store, craft supply shop, or online. The D-rings will come up with tiny screws to attach them.
    • Note that this will only work for wooden frames or frames made out of other pliable materials that you can screw into. Information technology will non piece of work for metal frames.

    Advertizing

  1. 1

    Select the right weight of wire for the size of frame you lot want to hang. Picture frame wire comes in different sizes that tin can support dissimilar weights. Choose a approximate of wire that can back up at least the weight of the frame you want to hang.[5]

    • For example, if the frame yous want to hang weighs 13 lb (5.9 kg), yous could apply 15 lb (vi.eight kg) picture frame wire.
  2. ii

    Cut a piece of wire to x cm (iii.9 in) longer than the width of the frame. Measure the width of the flick frame with a ruler or measuring tape and add 10 cm (3.9 in) to the width. Measure out the wire to this length and clip it with pliers.[6]

    • This will permit you to tie and secure the wire in identify while still leaving a piffling slack for hanging the frame.
  3. 3

    Tie the ends of the wires to the D-rings using slipknots. Insert the end of 1 wire upwards through the D-ring on 1 side, fold about 2–three cm (0.79–i.18 in) of the wire back and loop it around the long part of the wire once, then slip it back down through the D-ring to create a slipknot. Repeat this on the other side with the other cease of the wire.[7]

    • Make sure there is a little slack in the line later on you are done tying the ends to the D-rings. If the wire is directly beyond and tight with no slack, undo the slipknots and retie them with less wire.

    Tip: Leaving some slack in the wire puts less strain on it after the frame is hung. It also makes information technology easier to use 2 hanging hooks if you desire to.

  4. 4

    Twist the excess at the ends of the wire around the main length of wire. Pull the end of the wire on 1 side tight to brand certain the slipknot is tightened all the mode. Wrap the excess wire effectually the main length of wire like a spring coil, pulling information technology tight as you go. Echo this for the finish of the wire on the other side.[8]

    • If you accept a lot of excess wire at the ends, yous don't have to wrap all of it. You tin can just wrap information technology in 4-5 coils, and then clip off the rest of the excess wire with pliers.
  5. 5

    Hang the frame on your wall using a flick frame hanging hook. Install a picture frame hanging hook on your wall using the provided nail. Carefully place the frame against the wall over the hook and slide it down into place until the hook catches the wire on the back.

    • Make sure to use a hook that tin support the weight of the frame. The packaging will tell you the weight capacity of the hook.

    Advertisement

Ask a Question

200 characters left

Include your electronic mail address to get a message when this question is answered.

Submit

Advertisement

Thanks for submitting a tip for review!

Things You'll Need

  • Sticky felt bumps
  • Ruler or measuring tape
  • Pencil
  • 2 D-rings
  • Screws
  • Screwdriver
  • Picture frame wire
  • Ruler or measuring tape
  • Pliers
  • Picture frame hanging claw

Well-nigh This Article

Thanks to all authors for creating a page that has been read 26,124 times.

Did this article assist you?

schlateroneret.blogspot.com

Source: https://www.wikihow.com/Install-Picture-Frame-Wire

0 Response to "what knot to use for steel wire on d ring"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel